收藏本站
OPERATION
To Charge your Slam Stick?
Leave the device plugged into the USB port for
charging. A green LED will signify that the device is
charging. The LED will go out when a full charge has
been reached. A full charge will take 1 to 2 hours.
the device, an automatic erase will be performed.
The Slam Stick? will be delivered with a standard
configuration including a 10 second delay with a 30
second recording time. The g-level trigger will not be
enabled.
To Configure your Slam Stick?
The following parameters can be configured for your
device.
Pre-delay in seconds before recording
Values between zero and 86,400
Time after the button is pressed before the
recording starts
Number of samples recorded
Values between zero and 65535
Hit enter or zero if you would rather enter the
time of the recording
Recording time in seconds
Values between 1 and 220 seconds
How long the device will record data after
the pre-delay has ended
Hit enter or zero for no limit
G-Level Trigger
See Special Trigger Modes section for
more detail
To change settings such as recording pre-delay and
recording time, you can use either the ss_config.exe
program or (for Matlab? users) the 'ss_config.m' Slam
Stick Matlab script. Make sure any recordings you wish
to keep have been downloaded before you change
settings.
Whether using the .exe or Matlab, after asking a few
questions, the program will output a new 'config.dat' file
in the current working directory. Copy this file onto the
Vibration Recorder over the original. When you unplug
Multiple Recordings
Two methods are available to limit the size of each
recording, allowing you to continue taking recordings
until the flash memory is full. The recommended
method is to specify the number of seconds to record
for; however, the number of samples to record can also
be specified. If both settings are entered, recording will
stop if either condition is met. Please note that because
the recorder saves data in complete sectors (512
bytes) at a time, actual recording length may vary
slightly from the setting you enter.
Special Trigger Modes
Normally, recording or pre-delay begins immediately
after pressing and releasing the button. In some cases
it may be desirable to trigger recording only when a
certain G-level is exceeded. There are two G-level
trigger modes, depending on the nature of the event to
be measured and battery life required:
‘Nap’ sample rates (1-8Hz)
This is the lower power (longer battery life) trigger
mode and consumes ~ 60uA current. This mode is
best suited for sustained vibration events where it is not
necessary to record the beginning of the event. Since
the sample rate is very low, a brief G-level spike may
fall ‘in between’ samples and go unnoticed. In this
mode, the accelerometer is in a low-power idle mode,
the CPU is asleep and the Flash memory is powered
off. Thus, there will be a short delay between the first
recognized G-level exceedance and the start of
recording as the Flash memory is re-initialized.
REVISION N0. 001
REVISION DATE: 08-24-2010
www.mide.com
4
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
VSLY3850 IR EMITTER 850NM HIGH SPEED
VSLY5850 IR EMITTER 850NM HIGH SPEED DIP
VSMY2850G IR EMITTER 850NM HIGH SPEED SMD
VSMY7850X01-GS08 IR EMITTER 850NM HIGH SPEED SMD
VSOP38336 IC SIGNAL CONDITIONING 36KHZ QFN
WALLS-C4600-001 SYNJETWIRE HARNESS 4WIRE 600MM
WIT2410SDK DEVELOPMENT KIT, 2 WIT2410M MODU
WIT2411DK DEVELOPMENT KIT, 2 WIT2411M MODU
相关代理商/技术参数
VR02GC223MAA 制造商:AVX 功能描述:RMX322X2000 '93 .4LS S5J1C
VR05-1516LB 功能描述:CONV DC/DC 15V OUT 167MA 5W RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:VR-LB 标准包装:15 系列:Econoline REC3-DR 类型:隔离 输出数:2 电压 - 输入（最小）:4.5V 电压 - 输入（最大）:5.5V Voltage - Output 1:5V Voltage - Output 2:-5V Voltage - Output 3:- 电流 - 输出（最大）:300mA，300mA 电源（瓦） - 制造商系列:3W 电压 - 隔离:1kV（1000V） 特点:- 安装类型:表面贴装 封装/外壳:24-DIP SMD 模块（18 引线） 尺寸/尺寸:1.26" L x 0.80" W x 0.44" H（32.0mm x 20.3mm x 11.2mm） 包装:管件 工作温度:-40°C ~ 80°C 效率:75% 电源（瓦特）- 最大:3W 其它名称:10005457
VR05-FW 制造商:Custom Connector Corporation 功能描述:
VR05-LFW 制造商:Custom Connector Corporation 功能描述:Socket, Relay, Automotive Relay, 5 Pin Automotive, Crimp, Thermoplastic
VR05-PCB 制造商:Custom Connector Corporation 功能描述:Socket, Relay, Automotive Relay, 5 Pin Automotive, PC Board, Thermoplastic 制造商:Song Chuan Precision Company 功能描述:VR Series 5 Pin Socket PCB Micro Automotive Relay
VR05-SPCB 制造商:Custom Connector Corporation 功能描述:Automotive Relay Sockets 5 Pin
VR091B080CL 功能描述:DC/DC转换器 VRM 9.1 80A 12V to 1.10-1.85V RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
VR091B080CS 功能描述:DC/DC转换器 148W 12V/1.075-1.85V RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: